This website uses cookies to ensure you get the best experience on our website. Read more
Bose PowerMatch PM4500 Configurable Power Amplifier
Brand
BOSE
The Bose® PowerMatch PM4500 configurable professional power amplifier provides concert-quality sound with a high level of scalability and configurability for fixed installation sound reinforcement systems.
The Bose® PowerMatch PM4500 configurable professional power amplifier provides concert-quality sound with a high level of scalability and configurability for fixed installation sound reinforcement systems. Ethernet-equipped versions enable network configuration, control and monitoring, and an expansion slot supports input from optional digital audio accessory cards. PowerMatch amplifiers utilize numerous Bose technologies to deliver an unprecedented combination of performance, efficiency and ease of installation—all in a reliable, proprietary design.
Key Features
QuadBridge™ Technology – Allows the 4 available channels to be configured as Mono, V-Bridge, I-Share or Quad mode, allowing the total available power of the amplifier to be allocated to one or more output channels. The amplifier is capable of driving both low impedance and 70/100V loudspeaker loads directly.
Bose® ControlSpace® Designer™ software – PowerMatch amplifiers can be fully configured using ControlSpace Designer software via the onboard front panel USB connection, or the rear panel Ethernet connection (network models only). Using ControlSpace Designer software you can access additional features including: Parametric EQ stages, load sweep of each output channel and auto standby. ControlSpace Designer software is also used to integrate network model PowerMatch amplifiers into larger control and monitoring systems comprised of Bose ESP processors and CC control centers.
Auto-Standby/Auto-Wake function – When enabled, this function automatically enters/exits Standby Mode, allowing the system to consume less power.
Dual voltage and current feedback loop – Proprietary design combines Class-D efficiency with a unique current and voltage feedback loop circuit that continuously monitors and controls both the current and voltage delivered to the loudspeaker load. Independent of power level and load impedance, the amplifier consistently delivers the widest possible dynamic range, frequency response and lowest possible distortion.
PeakBank™ power supply – Regenerative 4-quadrant power supply enables higher power density while allowing the re-use of energy from reactive loads that is normally wasted in conventional Class-D designs. This highly efficient amplifier design delivers sustainable and repeatable low frequency response.
Fast-tracking power factor correction (PFC) – Efficiently manages the current drawn from the AC mains, allowing the amplifier to drive loudspeakers to maximum output longer without power fluctuation. PFC provides superior transient response and functions at peak burst power much longer than conventional Class-D amplifier designs to satisfy the requirements of even the most demanding program material.
Product Specs
| Maximum Rated Power | 2000 W (500 W x 4 channels at 4 ohms) |
| Peak Output Voltage | 71 / 142 V (Mono / V-Bridge, I-Share, and Quad modes) |
| Voltage Gain | 33 / 36 / 33 / 36 dB (Mono / V-Bridge / I-Share / Quad modes) |
| Frequency Response | 20 Hz - 20 kHz (at 1 W and +/- 0.5 dB) |
| Signal-to-Noise Ratio, Analog Input | > 102 dB (1 dB below rated power, A-weighted) |
| THD | < 0.4 % (at 1 W, 20 Hz to 20 kHz) |
| Intermod Distortion - SMPTE | < 0.4 % (60 Hz, 7 kHz) |
| Channel Separation (Crosstalk) | > 65 dB (adjacent channels, at 1 kHz) |
| Damping Factor | > 1000 (10-1000 Hz, 4 ohms, at amplifier output) |
| A/D and D/A Converters | 48 kHz / 24-bit |
| Total Latency (Analog In - Amp Out) | < 0.95 ms |
| Input to Output Signal Routing | 4 x 4 matrix |
| Loudspeaker Presets | Bose Professional |
| Input EQ | 5-band PEQ (+/- 20 dB), notch, shelving, high pass, low pass |
| Bandpass Filters (Crossover) | Butterworth, Bessel, or Linkwitz-Riley, up to 48 dB/octave |
| Loudspeaker EQ | 9-band PEQ (+/- 20 dB), shelving, high pass, low pass, 2-band RoomMatch® array EQ |
| Maximum Output Delay | 3 s |
| Output Limiter | Peak and RMS voltage |
| Output Channels | 1 to 4 (configurable) |
| Connectors, Output | 8-pin Phoenix Contact® connectors (part # 1778120), supports 10-24 AWG wire |
| LED Status Indicators | Signal, limit, clip, fault |
| User Interface Controls | Mute, input sensitivity, output configuration, output attenuation, EQ on/off, preset select. 240 x 64 LCD. Additional controls available w/ ControlSpace® Designer™ software |
| Mains Voltage | 100-240 V (50/60 Hz) |
| Mains Circuit Recommendation | 15A (120 V) or 10A (230 V) |
| Mains Connector | IEC 60320-C14 (Inlet) |
| Minimum AC Line Voltage | 80 V (reduced output power) |
| Maximum Inrush Current | 15.4 A (230 VAC, 50 Hz) |
| Maximum RMS Current Draw | 8 A |
| Efficiency, 1/3 Rated Power | > 73 % (pink noise input signal) |
| Output Stage Topology | Class-D |
| Overload Protection | High temperature, DC, HF, short, voltage limiter, current limiter, inrush current, mains circuit breaker protection |
| Dimensions (Enclosure only) | 3.5" H x 19" W x 20.7" D (88 mm x 483 mm x 525 mm)- 2 rack space |
| Shipping Weight | 30.0 lb (13.6 kg) |
| Mounting Depth | 21" (533 mm) |
| Operating Temperature | 32 °F - 104 °F (0 °C - 40 °C) |
| Cooling System | Microprocessor-controlled, variable-speed fans, front to rear airflow |
| Manufacturer | BOSE |
|---|
Write Your Own Review
