The gray WKE 191 Windscreen Set from Neumann is designed for use with the RSM 191 Stereo Microphone.

Pop screens provide excellent suppression of so-called pop noise, such as "p" or "t".

Pop screens provide excellent suppression of so-called pop noise, such as "p" or "t". They consist of a round, thin frame covered with black gauze on both sides.

Close range sounds, wind, and fast movements of the microphone boom, all may cause interfering noises. To avoid these unwanted sounds, windscreen accessories are available.

Close range sounds, wind, and fast movements of the microphone boom, all may cause interfering noises. To avoid these unwanted sounds, windscreen accessories are available.

Close range sounds, wind, and fast movements of the microphone boom, all may cause interfering noises. To avoid these unwanted sounds, windscreen accessories are available.

Close range sounds, wind, and fast movements of the microphone boom, all may cause interfering noises. To avoid these unwanted sounds, windscreen accessories are available.

Close range sounds, wind, and fast movements of the microphone boom, all may cause interfering noises. To avoid these unwanted sounds, windscreen accessories are available.

Close range sounds, wind, and fast movements of the microphone boom, all may cause interfering noises. To avoid these unwanted sounds, windscreen accessories are available.

Close range sounds, wind, and fast movements of the microphone boom, all may cause interfering noises. To avoid these unwanted sounds, windscreen accessories are available.

Close range sounds, wind, and fast movements of the microphone boom, all may cause interfering noises. To avoid these unwanted sounds, windscreen accessories are available.

Close range sounds, wind, and fast movements of the microphone boom, all may cause interfering noises.

Close range sounds, wind, and fast movements of the microphone boom, all may cause interfering noises. To avoid these unwanted sounds, windscreen accessories are available.

Close range sounds, wind, and fast movements of the microphone boom, all may cause interfering noises. To avoid these unwanted sounds, windscreen accessories are available.

Close range sounds, wind, and fast movements of the microphone boom, all may cause interfering noises. To avoid these unwanted sounds, windscreen accessories are available.

Close range sounds, wind, and fast movements of the microphone boom, all may cause interfering noises. To avoid these unwanted sounds, windscreen accessories are available.

Close range sounds, wind, and fast movements of the microphone boom, all may cause interfering noises. To avoid these unwanted sounds, windscreen accessories are available.

Close range sounds, wind, and fast movements of the microphone boom, all may cause interfering noises. To avoid these unwanted sounds, windscreen accessories are available.

Tripod adaptor plate (115 mm) to mount on König & Meyer tripods No. 26790 and No. 26795.

This Nomad Speaker Stand is strong and light, made mostly out of aluminum. The ends are reversible - one side is 1-3/8" and the other is 1-1/2", so you don't need any adaptors! A locking pin gives you added security. The retractable leg housing gives the stand a low center of gravity for high stability, and when you're done the legs can fold up for easy storage and schlepping. You can adjust this speaker stand from 44" to 72" tall.

The Nomad Nmc-J802 Mic clip is made of durable soft rubber and fits most standard vocal microphones, and features a standard 5/8" thread Soft Rubber Microphone Clip will fit most standard dynamic and wireless microphones. 5/8” Thread fits most standard microphone stands. Soft Rubber Construction is extremely durable, even in cold temperatures.

This Nomad Speaker Stand is strong and light, made mostly out of aluminum. The ends are reversible - one side is 1-3/8" and the other is 1-1/2", so you don't need any adaptors! A locking pin gives you added security. The retractable leg housing gives the stand a low center of gravity for high stability, and when you're done the legs can fold up for easy storage and schlepping. You can adjust this speaker stand from 44" to 72" tall.

Electronics Voltage 100-120V Wattage LF Amplifier - 80W, HF Amplifier - 65W Hardware Cabinet Material Vinyl-Laminated, Medium-Density Fiberboard Miscellaneous Connection Type IEC Monitors Protections RF Interference Output-Current Limiting Over-Temperature Turn-On/Off Transient Subsonic Filter External Mains Fuse Audio Controls Volume Range: A-Type TaperMF Control: Variable (-6 to +6 dB)HF Control: Variable (-6 to +6 dB)Low Cut: Flat, 80 Hz, 100 HzAcoustic Space: Flat, -2 dB, -4 dB Peak SPL 106 dB (at 1 Meter) Crossover Frequency 2.4 kHz Monitor Inputs 1 x Balanced XLR, 1 x Balanced 1/4"TRS, 1 x Unbalanced RCA HF Transducers 1.25” Silk Dome Tweeter LF Transducers Dual 6.5" Frequency Response 45 Hz – 22 kHz Input Impedance 10 kΩ Monitor Amplifier Power LF Amplifier - 80W, HF Amplifier - 65W Specifications Input Impedance 10 kΩ

The R65's custom 6.8-inch Air Motion Transformer (AMT) ribbon tweeter responds to the subtlest waveforms and the highest frequencies, resulting in a greater sense of"air"and"space"that is characteristic of audiophile recordings. Custom coated, woven, 6.5-inch LF drivers produce a more dynamic output than conventional designs, thanks to the rigid cone's ability to maintain a more constant dispersion pattern across its frequency response range. The result is transparent sound with narrow vertical dispersion, which reduces undesirable reflections, and broad horizontal dispersion for a wide sweet spot. Driven by a 150W Class D amplifier, the biamped R65 delivers an open, clear, and less fatiguing listening experience. Features 2-way active AMT design provides articulate high-frequency response and wide stereo imaging Custom-designed, 6.8-inch, AMT ribbon tweeter responds to the subtlest waveforms and the highest frequencies 6.5-inch Kevlar LF drivers provide transparent mid- and low-frequency reproduction for clean sound and punchy bass Biamped 150W RMS (LF = 100W, HF = 50W), Class D power amplifier with switching power supply Acoustic Space settings (Linear, -1.5 dB, -3 dB, -6 dB) compensate for room placement Balanced XLR and ¼-inch TRS plus unbalanced RCA inputs provide flexibility for seamless integration into any environment RF interference, output current limiting, over temperature, turn-on/off transient, and subsonic filter protection Interchangeable black faceplate included Energy Conservation Mode (with enable/disable) lowers standby power to <0.5W External mains fuse Power: 100-120V, 60 Hz or 220-240V, 50 Hz

MiCon Connector for 3.5mm Select Stereo Devices

Wind Shield and Shock Mount System

PG2 Pistol Grip with Shock Mount The PG2 is a high-quality pistol grip for using shotgun microphones and other compatible microphones in handheld applications. It features a shock mount system for minimising handling noise, which can accommodate microphones with a diameter of 19-20mm or 21-22.5mm using the supplied interchangeable mounts. It features a handy release lever on the mount for quick and easy adjustment of the microphone angle, cable management, and a 3/8-inch thread on the base for attaching the grip to boompoles and microphone stands. Key Features: High-quality pistol grip for shotgun microphones Shock mount system for minimising handling noise Integrated cable management system 3/8-inch thread on base for use with a boompole

Lightweight Boompole - 2m

MiCon Connector for Select Sennheiser Devices

MiCon Connector for 3-pin XLR Devices